Trusted in Aerospace Industry for Over 20 Years
Trusted in Aerospace Industry for Over 20 Years
Accurate
±1% Torque | ±1° Angle
Easy
Compact | Simple Operation | Intuitive Interface
Versatile
Adapts to multiple applications | Automation | Data Exporting
Accurate
±1% Torque | ±1° Angle
Easy
Compact | Simple Operation | Intuitive Interface
Versatile
Adapts to multiple applications
Automation | Data Exporting
Virtual Wrench Tour:
Hover over large image and click any component that highlights orange on the wrench or display to see details.
Virtual Wrench Tour:
Hover over large image and click any component that highlights orange on the wrench or display to see details.
Digital Torque Multiplier
Digital Controller
Anti-Rotation Cover
The anti-rotation assembly is used to safely prevent motion opposite to the direction of applied torque. It has a ratcheting pawl that enables operators to toggle between clockwise, neutral, and counter-clockwise input directions.
High Reduction Gearbox
The high gear reduction grants operators the mechanical advantage to apply significant levels of output torque with little manual input required. With this gearbox, a single operator can effortlessly torque even the most demanding of applications with a standard input ratchet.
Labeling
Every wrench is clearly marked with a unique serial number and torque rating for identification. By request, ATP can modify the label to meet your identification standards.
Housing
Patented design ensures accuracy and durability between calibrations.
Reaction Pins
Reaction pins allow for symmetric load distribution to counteract the torque applied without introduction of pinch points. Customizable adapter plates with variable pin size and spacing allow for one tool to be used across several different applications.
Drive
Customizable output drives (square, hex, spline, castellated, etc.) can be designed to suit any application.
Shop Grip
Centrally located no-slip handles provide users enhanced comfort and mobility in any environment.
Units
The UNITS button cycles through all available units programmed in the controller. The selected unit label will display next to the torque value on the LCD screen. By default, ATP includes ft·lb and in·lb scales, but additional unit scales (including metric) can be enabled/disabled by customer request.
Display Modes (TRACK)
Track mode displays the torque value the current torque sensed by the tool in real time. Typically used for calibration and verification, track mode allows the operator to precisely hold torque at predetermined data points.
Display Modes (PEAK)
Peak mode displays the maximum torque reading measured by the tool during that torque sequence. This value remains on the LCD screen until the maximum value is exceeded maximum or the operator manually clear it by pressing the ZERO button. Peak mode is recommended for measuring the maximum applied torque to a joint during installation and breakaway.
Display Modes (ANGLE)
Angle mode displays the current angle heading of the output drive in real time. The ZERO button is used to reset the angle value and establish a reference point to measure from. Torque can be monitored simultaneously with angle in either TRACK or PEAK mode.
LCD
A backlit LCD display provides clear torque and angle values that can be easily seen in any environment. The display provides torque and angle resolutions as fine as 2 in·lbs and 1 minute of arc, respectively.
Alarms
Alarms can be set at specified targets to alert the operator that a specific torque has been achieved. When enabled, the target torque value will be shown in the lower right corner of the display. Available across all display modes, the alarm triggers an audible tone and illuminates a red LED to signify that the user has met or exceed the designated torque value.
Zero
Allows user to zero torque or angle values on the display.
Data Capture
The PRINT button allows data from the display to be streamed over a serial connection. Paired with an RS232 interface, torque and angle logs can be easily derived to record and audit various applications.
Power
Toggle display on or off. The controller can sustain eight hours of continuous use before recharge.
Digital Torque Multiplier
Anti-Rotation Cover
The anti-rotation assembly is used to safely prevent motion opposite to the direction of applied torque. It has a ratcheting pawl that enables operators to toggle between clockwise, neutral, and counter-clockwise input directions.
High Reduction Gearbox
The high gear reduction grants operators the mechanical advantage to apply significant levels of output torque with little manual input required. With this gearbox, a single operator can effortlessly torque even the most demanding of applications with a standard input ratchet.
Labeling
Every wrench is clearly marked with a unique serial number and torque rating for identification. By request, ATP can modify the label to meet your identification standards.
Housing
Patented design ensures accuracy and durability between calibrations.
Reaction Pins
Reaction pins allow for symmetric load distribution to counteract the torque applied without introduction of pinch points. Customizable adapter plates with variable pin size and spacing allow for one tool to be used across several different applications.
Drive
Customizable output drives (square, hex, spline, castellated, etc.) can be designed to suit any application.
Shop Grip
Centrally located no-slip handles provide users enhanced comfort and mobility in any environment.
Digital Controller
Units
The UNITS button cycles through all available units programmed in the controller. The selected unit label will display next to the torque value on the LCD screen. By default, ATP includes ft·lb and in·lb scales, but additional unit scales (including metric) can be enabled/disabled by customer request.
Display Modes (TRACK)
Track mode displays the torque value the current torque sensed by the tool in real time. Typically used for calibration and verification, track mode allows the operator to precisely hold torque at predetermined data points.
Display Modes (PEAK)
Peak mode displays the maximum torque reading measured by the tool during that torque sequence. This value remains on the LCD screen until the maximum value is exceeded maximum or the operator manually clear it by pressing the ZERO button. Peak mode is recommended for measuring the maximum applied torque to a joint during installation and breakaway.
Display Modes (ANGLE)
Angle mode displays the current angle heading of the output drive in real time. The ZERO button is used to reset the angle value and establish a reference point to measure from. Torque can be monitored simultaneously with angle in either TRACK or PEAK mode.
LCD
A backlit LCD display provides clear torque and angle values that can be easily seen in any environment. The display provides torque and angle resolutions as fine as 2 in·lbs and 1 minute of arc, respectively.
Alarms
Alarms can be set at specified targets to alert the operator that a specific torque has been achieved. When enabled, the target torque value will be shown in the lower right corner of the display. Available across all display modes, the alarm triggers an audible tone and illuminates a red LED to signify that the user has met or exceed the designated torque value.
Zero
Allows user to zero torque or angle values on the display.
Data Capture
The PRINT button allows data from the display to be streamed over a serial connection. Paired with an RS232 interface, torque and angle logs can be easily derived to record and audit various applications.
Power
Toggle display on or off. The controller can sustain eight hours of continuous use before recharge.
Wrench Packages
Included Items
Torque Multiplier
Digital Torque Multipliers are available in various capacities as high as 40,000 ft·lbs (480,000 in·lbs) with accuracy of up to ±0.4% full-scale torque. All Digital Torque Multipliers are designed to meet customer specifications and include customized drives and reaction tooling.
Electronics Package
The Digital Display is an intuitive interface to provide operators with accurate torque and angle readings as well as provide additional features such as alarms and data logging capabilities. Electronics package includes associated wrench cable and charger.
No FOD Ratchet
FOD (Foreign Object Damage) free 1/2″ drive black-oxide ratchet allows operator to safely apply torque in any environment.
Protective Case
Durable case custom fit to each Digital Torque Multiplier to ensures safe transport of calibrated product and accessories.
Operator Package
Comprehensive operation manual gets users up to speed quickly.
Calibration
All Digital Torque Multipliers are calibrated and traceable to N.I.S.T. standards. Certificates are provided with every calibration include torque and angle as-found and as-left readings for both clockwise and counter-clockwise directions.
Upgrades
Angle
Angular output capabilities are available to allow operators to monitor turn of nut procedures simultaneously with output torque. Our display allows for a resolution of 1 arcminute and stated accuracy of ±1 degree.
Learn More
High Accuracy
Advanced Torque Products offers an expanded HA line of Digital Torque Multipliers with accuracy of ± 0.40%. Clearly distinguished by their orange handles and label, these tools are designed for applications demanding the highest accuracy and repeatability.
Learn More
Mounting
Detachable mounts secure to the housing of your wrench and firmly the display for hands-free viewing, leaving an operator free to focus on the task at hand.
Learn More
Electronics
The next generation in our Digital Display includes a durable 8” touch screen display (MIL-STD-810G and IP68-cerified) with improved UI to provide an even more intuitive torquing experience. Procedure creation functionality and expanded data logging features will provide consistency and traceability while improving overall process efficiency.
Learn More
Speed Knob
Our speed knob is a valuable tool to allow operators to quickly apply low torque in applications with run on, saving time while still allowing a ½” passthrough for use with a standard input ratchet.
Learn More
Drill Adapter
The drill adapter fits over the existing anti-rotation cover and eliminates need for any manual input from the operator. Instead of requiring a ratchet, users can use a drill to quickly apply torque, increasing safety and process efficiency.
Learn More
Automated Motor Drive
The new motor drive system was developed to make accurate assembly even easier. It eliminates manual input from an operator by working in tandem with our Drill Adapter and providing input to our AeroTorque™ multipliers directly. The motor can be controlled with a pendant or by choosing to have it automate with our “Procedures” feature in our new controller.
Learn More
Tooling Design
Reaction Stands
Reaction stands allow for symmetric load distribution to counteract the torque applied without introduction of pinch points. Reaction stands are designed with stress concentration in mind, minimizing the possibility of inadvertent damage to nearby structures that may otherwise occur with traditional reaction bars.
Learn More
Drive Bars
Advanced Torque Products will design and produce custom drive bars to integrate any multiplier to your specific application. Available output profiles include but are not limited to:
• Square
• Hex
• Spline
• Castellated
Learn More
Sockets
In addition to custom drive bars, Advanced Torque Products will design and produce accompanying sockets to allow a single multiplier to be used across numerous different applications.
Learn More
Adapters
Along with the standard adapters readily available, ATP will also design and produce custom adapters to integrate with your multiplier and specific application.
Learn More
U.S. Patent Nos. 8,434,389 & 8,991,284
European Patent No. 2396147
Canadian Patent No. 2,752,088
Japanese Patent No. 5699338
U.S. Patent Nos. 8,434,389 and 8,991,284
European Patent No. 2396147
Canadian Patent No. 2,752,088
Japanese Patent No. 5699338
